Exterior Roof  
           

EXTERIOR ROOF Ceramic InsulCoat R:E

  is now listed in the Rated Product Directory of the

Cool Roof Rating Council (CRRC).

              

       

        What does Cool Roof Rated mean:

       According to the United States Environmental Protection Agency:

For millions of Americans living in and around cities, heat islands are of growing concern.   This phenomenon describes urban and suburban temperatures that are 2 to 10° F (1 to 6°C) hotter than nearby rural areas.   Elevated temperatures can impact communities by increasing peak energy demand, air conditioning costs, air pollution levels, and heat related illness and mortality.

Click here for more information on the benefits of COOL ROOF.

  

   Ideal for all Industrial, Commercial and Residential Buildings

For use on Composite Fiberglass Shingles * Asphalt Shingles * Various Membrane Systems * Concrete and Fired Clay Tiles * Primed Metals

CERAMIC INSULCOAT-ROOF provides beautification, UV protection & thermal barrier enhancement. It is a strong, tough coating, formulated with "CERYLIUM", a proprietary formula of percision blended high performance ingredients, in a complex, 100% acrylic suspension with superior adhesion, breathability, elasticity and weatherproofing.  It is designed to provide the ultimate protection against Ultra-Violet degradation and weathering. Ceramic InsulCoat ROOF has demonstrated significant thermal resistance under laboratory tests when compared to Batt Insulation.

Ceramic InsulCoat Roof Benefits

Thermal Barrier - Ceramic particulate plus high titanium levels provide significant thermal barrier protection.

Energy Efficient - Reflected heat rays increase efficiency.  Slowing the movement of heat through the substrate provides heat management, greater comfort and reduced energy consumption.

Fire Resistant - Self-extinguishing, does not support flame spread.  Environmentally Friendly 100% acrylic water-based product that meets today's strict environmental guidelines.

Titanium Dioxide Enriched - Titanium Dioxide is an excellent UV inhibitor.

Weatherproof Enhancement - Creates a weather-proof membrane that significantly reduces potential damage and deterioration of the substrate.  Reduces rot and mildew formation.

Flexible - Designed to resist improvement caused by thermal impact.

Limited Colour Choices - Resists fading.  White and pastel colours available.

Suggested Preparation Procedures

*Repair all leaks

*Pressure wash and clean, or airbrush and clean substrate.  Remove all loose materials.

*Apply Ceramic InsulSeal to porous substrates.

*Finish with Ceramic InsulCoat ROOF for protection, insulation and beautification.

Performance Characteristics

Thermal Characteristics - "The Envirocoat Inc., Ceramic InsulCoat provided a greater thermal difference between the coated side and the uncoated side. The leading brand of exterior latex paint provided a much less thermal barrier difference. The conclusion, therefore, is that the Ceramic InsulCoat definitely provides a much better insulating factor than a regular exterior latex". (LS Consulting)

"From the testing completed, it is apparent that the Envirocoat Inc. Ceramic InsulCoat membrane provides a thermal barrier against heat and cold thermal transmission, as tested in comparison with batt insulation." (Inchcape lWarnock Hersey Professional Services. Ltd.)

Product Data  

Characteristics Test Method Observation
Weight per US G (3.78L) FTMS 141 -Method 4184 11 Lbs (4.99Kg)
Non-Volatile Solids FTMS 141 -Method 4041

By weight: 69.1%

By volume: 60.9%
Viscosity FTMS 141 -Method 4281 Stormer Viscosity: 100 revolutions in 8 seconds at 500 grams
Toxicity FTMS 141 -Method 511

Material is non-toxic & requires no special ventilation during application.

Contains no materials considered to be health hazards.
Flammability ASTM 1360 -DOT-MVSS 302

In container: Non-flammable

On concrete: Self-extinguishing -does not support flame spread.
Package Stability  

One year + after opening: no settling or other undesirable effects.

Materials completely dispersed after stirring
Abrasion Resistance

FTMS 141 -Method 6192

Tabor C17 Wheel -100 grams -1000 cycles

Weight loss in grams:

InsulCoat Roof with aggregate: ..............41g

InsulCoat Roof without aggregate: .........14g

Epoxy floor coating without aggregate: ....9g   (Typical)
Impact Resistance ASTM D2794 28 inch-pounds of impact with no break in the film surface. Typically, 20 inch-pounds of impact is considered to be a high performance test result.
Flexibility ASTM D 522 -Method B Withstood deformation of 1-inch on a metal substrate at zero degrees Fahrenheit (-18 degrees C) with no loss of adhesion, cracking, chipping or flaking (mandrel test).
Elongation ASTM D 2370 12 mils -0.31mm dry film thickness stretched 160% with 100% full memory. This was the full extent of the elongation and the film never did break.
Water Resistance (wind-driven rain)

TTC-555

Water driven against test surface at a dynamic pressure equivalent to 98 mph

Time for water to penetrate:

One Coat: &&&6.3 mils &&&..30 minutes

Two coats: &&..10.0 mils &&&11 hours
Moisture Vapour Transmission

ASTM D 1653 Wet Cup Method, inverted

24.9 perms

A "perm" is a unit of measure expressing a coating's ability to allow moisture vapour to pass through the film, or its "ability to breathe". The lower the "perm" rating, the more likely the coating will blister over time.
High Humidity Resistance

FTMS 141 -Method 6201

100% condensing humidity at 107° F -41.67° C

336 hours with no evidence of film deterioration, blistering or peeling from substrate

(250 hours required to pass Federal Specifications)
Salt Spray

FTMS 141 -Method 811.1

100% condensing 5% salt fog at 95° F -35° C

336 hours with no evidence of film deterioration, blistering or peeling from substrate

(250 hours required to pass Federal Specifications)
Accelerated Weathering

ASTM D 4798 / G155(a)

 No cracking or checking after 1,000 hours accelerated weathering.
Fungus Resistance FTMS 141 -Method 6271 No fungus growth when material tested in an environment of three organisms

Solar   Reflectance          

 Cool Roof Rating Council                 0 .88  Initial test results                                               
Thermal Emittance Cool Roof Rating Council 0.87 Initial test results       
 

Application Characteristics

Material                                           Single component, ready-to-use from container with little or no stirring required
Approximate Coverage

Rough porous surface: .................................... 100 to 175 sq. ft/gallon

Smooth, tight surface: ..................................... 175 to 225 sq.ft./gallon
Dry Base Film Thickness

One coat: ......................................................... 5 to 7 dry mils

Two coats: ...................................................... 10 to 12 dry mils
Substrate Preparation Dry, clean, tight surface with no gloss. -will bridge hairline cracks.
Application Temperature Range 39° F -4° C substrate to 80° F -29° C ambient air in direct sunlight
Application Method 1.5" nap roller -brush -airless sprayer (0.023" -0.584mm tungsten-carbide tip)
Initial Cure (tack-free)   Air dry, 15 to 30 minutes with moderate to low ambient humidity
Primary Cure Air dry, 48 hours at 60° F -15.5° C or greater surface temperature with moderate to low ambient humidity
Final Cure 90 to 120 days
Solvent (before curing) Water
Cohesion Strength

Outstanding bond to dry or slightly damp surfaces. Strong cohesion to any clean, dry concrete, cement, wood, asphalt, clay tile   and primed metal surfaces.

Hydrostatic pressure will disrupt this bond.

      Manufacturers of High Performance Coatings and Paints Since 1960!

                              Download Envirocoatings Exterior Roof printable PDF versions.

MSDS

Technical Data


 
Investor Information | News Release Overview | Home Page | Corporate Profile | Corporate Directory | Management Team | Board of Advisors | History | Products Overview | Exterior Wall | Exterior Roof | Insulseal | Seal Bond | Contact Us | British Columbia | Alberta | Saskatchewan | Manitoba | Ontario | Quebec | New Brunswick | Newfoundland | Nova Scotia | Prince Edward Island | United States | Single Family | Multi Family | Commercial | Institutional | Specialty | Videos | Sitemap | Site Admin
All contents © envirocoatings.com 2007 ALL RIGHTS RESERVED,
Site Design by WPX Web site Design Canada