|
Ceramic InsulCoat Exterior Wall Benefits
Long-Lasting Finish - Lasts up to three (3) times longer then paint.
Thermal Barrier - Protection. Ceramic particulate reflects heat, enhances heat management and extends life-cycle performance factors.
Energy Efficient - Ceramic InsulCoat R:E Exterior Wall and Roof Coatings Systems helps reduce energy by reflecting heat rays away from the coated surface. End users report up to forty (40%) percent reduction in energy consumption, plus greater creature comfort.
Fire Resistant - Does not burn in the pail. Self-extinguishing, does not support flame spread.
Environmentally Friendly - 100% acrylic water-based product that meets today's strict environmental guidelines.
Breathable - Allows water vapour to escape from the interior.
Titanium Dioxide Enriched -
Is an excellent UV inhibitor.
Weatherproof - Creates a weatherproof membrane that significantly reduces potential damage and deterioration of the substrate. Reduces rot and mildew formation.
Flexible - Expands to 160% with full memory return. Withstands normal building expansion and contraction. Resists chipping, flaking or peeling.
Easy Maintenance - Easy to wash with municipal water pressure and conventional techniques.
Colour-Fast - Full range of colours. Resists fading. White, pastels, bright and accent colours available.
Simple 5-step Restoration Process
Pressure wash and clean, or airbrush and clean substrate.
Remove all loose materials.
Repair all leaks. For substrate restoration, Master Painters preparation guidelines are recommended. Use proper envelope or substrate preparation systems.
Apply Ceramic InsulSeal to porous substrates. Appropriate primers may be required.
Finish with Ceramic InsuICoat WALL for protection, enhanced thermal barrier and beautification.
Ceramic InsulSeal is a specially formulated soaker-sealer designed to penetrate porous substrates and provide superior micro-mechanical anchoring points. Ceramic InsulPatch is a cementitious compound easily used to emulate a wide variety of substrate profiles. May be used to fill cracks to exact requirement.
Product Data
|
Characteristics |
Test Method |
Observation |
|
Weight per
US G (3.78L) |
FTMS 141 - Method 4184 |
11 Lbs (4.99Kg) |
|
Non-Volatile Solids |
FTMS 141 - Method 4041 |
By weight: 69.1%
By volume: 60.9% |
|
Viscosity |
FTMS 141 - Method 4281 |
Stormer Viscosity: 100 revolutions in 8 seconds at 500 grams |
|
Toxicity |
FTMS 141 - Method 511 |
Material is non-toxic & requires no special ventilation during application.
Contains no materials considered to be health hazards. |
|
Flammability |
ASTM 1360 - DOT-MVSS 302 |
In container: Non-flammable
On concrete: Self-extinguishing - does not support flame spread. |
|
Package Stability |
|
One year + after opening: no settling or other undesirable effects.
Materials completely dispersed after stirring |
|
Abrasion Resistance |
FTMS 141 - Method 6192
Tabor C17 Wheel - 100 grams - 1000 cycles |
Weight loss in grams:
InsulCoat Roof with aggregate: ..............41g
InsulCoat Roof without aggregate: .........14g
Epoxy floor coating without aggregate: ....9g
(Typical) |
|
Impact Resistance |
ASTM D2794 |
28 inch-pounds of impact with no break in the film surface. Typically, 20 inch-pounds of impact is considered to be a high performance test result. |
|
Flexibility |
FTMS 141 - Method 6222 |
Withstood deformation of 1.5" - 38mm to 1/8" -3.2mm on a metal substrate with no loss of adhesion, cracking, chipping or flaking (mandrel test). |
|
Elongation |
ASTM D2370 |
12 mils - 0.31mm dry film thickness stretched 160% with 100% full memory. This was the full extent of the elongation and the film never did break. |
|
Water Resistance (wind-driven rain) |
TTC-555
Water driven against test surface at a dynamic pressure equivalent to 98 mph |
Time for water to penetrate:
One Coat: &&&6.3 mils &&&..30 minutes
Two coats: &&..10.0 mils &&&11 hours |
|
Moisture Vapour Transmission |
ASTM E96 - Procedure B |
20.0 perms
A "perm" is a unit of measure expressing a coating's ability to allow moisture vapour to pass through the film, or its "ability to breathe". The lower the "perm" rating, the more likely the coating will blister over time. |
|
High Humidity Resistance |
FTMS 141 - Method 6201
100% condensing humidity at 107° F - 41.67° C |
336 hours with no evidence of film deterioration, blistering or peeling from substrate
(250 hours required to pass Federal Specifications) |
|
Salt Spray |
FTMS 141 - Method 811.1
100% condensing 5% salt fog at 95° F - 35° C |
336 hours with no evidence of film deterioration, blistering or peeling from substrate
(250 hours required to pass Federal Specifications) |
|
Artificial Weathering |
ASTM E42 - Carbon Arc weatherometer
250 hours equivalent to 5 years |
After weatherometer testing (simulated rain, heat, ultra-violet ray and normal weather cycling) the coating showed no evidence of chalking, blistering or peeling, cracking or checking and only slight yellowing of the 100% titanium dioxide white colour. |
|
Fungus Resistance |
FTMS 141 - Method 6271 |
No fungus growth when material tested in an environment of three organisms |
|
Material |
Single component, ready-to-use from container with little or no stirring required |
|
Approximate Coverage
Dependent on application methods |
Rough porous surface: ....................................
100 to 175 sq. ft/gallon
Smooth, tight surface: .....................................
175 to 225 sq.ft./gallon |
|
Dry Film Thickness |
One coat: .........................................................
5 to 7 dry mils
Two coats: ......................................................
10 to 12 dry mils |
|
Substrate Preparation |
Dry, clean, tight surface with no gloss. - will bridge hairline cracks |
|
Application
Temperature
Range |
39° F - 4° C substrate to 80° F - 29° C ambient air in direct sunlight |
|
Application Method |
1.5" nap roller - brush - airless sprayer (0.023" - 0.584mm tungsten-carbide tip) |
|
Initial Cure (tack-free)
|
Air dry, 15 to 30 minutes with moderate to low ambient humidity |
|
Primary Cure |
Air dry, 48 hours at 50° F -
15.5° C or greater surface temperature with moderate to low ambient humidity |
|
Final Cure |
90 to 120 days |
|
Solvent (before curing) |
Water |
|
Cohesion Strength |
Outstanding bond to dry or slightly damp surfaces. Strong cohesion to any clean, dry concrete, masonry, asphalt, brick or wood surfaces.
Hydrostatic pressure will disrupt this bond. |
|
Specification for application |
Envirocoatings requires a two-coat system of 10-12 dry mils over a clean, dry, sound substrate. In some cases where minor dusting off is occurring and the substrate has been properly cleaned according to MPDA standards, Insulseal or Insulseal 5.0 may be applied as a penetrating conditioner, to help solve this problem. Due to the nature of dusting off this system will only work where minor dusting off is occurring. |
Manufacturers of High Performance Coatings and Paints Since 1960! |
